Of course, you need bootcamp to be able to boot both of these (maybe you could install osx to another hd or something).With a new PC, you might be looking to buy a copy of Windows 10. Forum rumor has it that if you boot first to osx and then reboot into windows 7 that osx will start it for you and then you can use xp mode. But macs don't have "bioses" so you'll have no way to do this after you install. if you want to use "xp mode" with windows 7, you have to enable your hardware virtualization in the bios. To install Windows on your Mac using Boot Camp, follow the steps listed below in the order listed: Notes: Had similar experiences with Adobe on parrallels in OSx.Windows to Mac. Download was a little slow (hence the time it took), but with a little.You can use VMLight instead, but I installed itunes on that and it just crashed without running. Download instructions on Amazon were accurate, and I had Office installed on my new desktop in about 20-30 minutes.
Buy Drivers From TheUnless you're putting everything on one big raid volume and booting straight from that, osx isn't really hurting anything except a few megs off your boot volume, but that's not typically a problem.(I didn't install any drivers from the disk and didn't have any problems)Environment: any MBP/MBA having GPT (yes GPT, not MBR, because 10.11/10.12/Sierra/etc will not allow you to have MBP partitioned drive and installed on it, especially on wireless recovery mode). You have to hold down the "alt" key when it's rebooting and then select the hard drive to boot from, otherwise you will be stuck with a white/grey screen.When you are done with the install, reboot and hold down "alt" and then control-click the windows-7 drive to make it the default boot volume and you don't have to hold "alt" down anymore on restart.As others have said, it's probably best to just use bootcamp and set windows as the default. The steps are the same for the Windows 10 operating system, however, your screen may look.There's some general issues with booting macs that most users probably know already, but I did not:Do the disk util thing the way the vista instructions describe.When you reboot with your windows 7 cd, it will do some initial instally-things and then reboot your computer. It will require to append hybrid MBR partition emulation (without boot flag enabled!). Refind will let you choose what media to boot from including: USB stick with windows 7 installation image and HDD partition with already installed windows 7 (later)Step 4: download and install gdisk. Make sure you have NTFS formatted stick otherwise it will not boot installation after.Step 2: repartition your hdd drive using regular macosx disk utility (let it stay in GPT mode, it won't matter for you anymore).Step 3: download and install refind boot loader replacing original useless MBP/MBA pseudo-bootloader (you can always comeback to the original one by holding "alt" key during boot process). The best way to do so is to use unetbootin. Trying to install windows 7 using boot-camp will complain about single only partition you must have on your HDD and will complain about installing ONLY from DVD disk (imaging the hassle as modern MBP/MBA has NO DVD drive embedded at all)Step 1: you have to migrate windows 7 installation from DVD drive/image into USB stick. Format a mac drive for windowsIf you specify bootable flag 'y' - you'll have a windows 7 usb stick bootloader failure (it will discover bootable win7 partition on your hdd and will try to boot from it instead).Step 5: plug windows 7 usb stick and reboot. Write table to the disk (command 'w'). Answer 'n' on "use one to protect other". Make hybrid MBR (command 'h'): specify windows 7 dedicated partition number (single digit), answer 'y' on place EFI GPT partition first, answer "default" on MBR hex code (just hit Enter), answer 'n' on set the bootable flag. Then switch into "recovery and transformation mode" (command 'r'). Print list of partitions (command 'p') and remember the one you've created for future windows 7 installation. Remove the stick once the windows will enter reboot state.Step 6: plug in fat32 formatted usb stick with WindowsSupport folder you've downloaded with the help of boot-camp application. The rest of installation process will be relatively simple and standard. Don't delete the partition but I'd suggest to format it within the menu. Inside windows install select "advanced" installation and choose preselected partition by yourself. Reboot system and you are done with the 2 systems booting in parallel from the refind bootloader.
0 Comments
Leave a Reply. |
AuthorAdam ArchivesCategories |